Log Wood Face Veneer Rotary Peeling Machine-manufacture,factory,supplier from China

The demand for wood veneer dryer is increasing year by year,and it has been recognized and purchased by consumers.Traditional natural air-dried wood is prone to problems such as deformation and cracking.The use of wood dryer equipment can effectively solve this problem.The cost of dryer equipment is high, so basic maintenance needs to be done in the later use process,such as the ground,ventilation system, gate,instrument,heating system and debugging system,etc.The specific operations are as follows:1.The floor of the wood dryer equipment should be kept clean and tidy,and the debris should be c

The 2024 Turkish International Woodworking Exhibition will be held in Istanbul from October 12th to 16th. As a manufacturer of veneer drying equipment, we are very honored to participate in the Turkish International Woodworking Exhibition and will present our products and product solutions face-to-face with global customers at booth 904B.During the exhibition, we had in-depth exchanges with customers and partners from different countries.

In the stage you are catching up with a wide range of development, the lack of supply will affect the pace of industrial progress, rotary drying machine equipment manufacturing is a strategic industry in the national economy, the equipment level is equipped with a strong level, the country is strong, "a Wenbin" has many favorable elements for the future development of our country equipped with manufacturing operations, the domestic market potential is huge, rich resources. Money, rich human resources, the key is our approach and how to make better use of it.

Birch veneer has a high shrinkage rate after drying because it is made up of thin layers of wood that have been peeled or sliced from the birch log. When the veneer is dried, the moisture is removed from the wood, causing it to shrink in size.There are several factors that can contribute to the high shrinkage rate of birch veneer after drying. One of the main factors is the orientation of the wood fibers. Birch veneer is typically sliced or peeled from the log in a direction that follows the grain of the wood.

Rotary cutting veneer dryer equipment has the characteristics of fast and monotonous, good uniformity, high energy efficiency ratio, small footprint, no environmental pollution, etc., can be widely used in various wood drying treatment. Equipped with infrared temperature measurement, low noise transmission system, active loading and unloading system. GMP manufacturing standards, microwave leakage is less than 1mw/㎡, strict implementation of relevant safety standards.

As a leading veneer drying equipment manufacturer, we are honored to participate in the 2024 Shanghai International Furniture Production Equipment and Woodworking Machinery Fair (Furniture China & Woodworking Machinery Fair), and will be at booth 7.1D72 to showcase our new technologies and product solutions face-to-face with global customers.The exhibition will be held from September 11th to 14th for four days.

The rotary veneer dryer is used for drying wood, which has the advantages of energy saving, reliability, short cycle, high quality and low cost. Widely used in all kinds of wood processing enterprises, especially suitable for wood products export enterprises. HGG series drying equipment, during normal operation, the fuel is fully burned in the combustion room, and the heat exchange system generates high temperature air.

Faults of the board dryer are as follows: 1. Failure analysis of rotary granulator: the main engine current is unstable. Production reasons: uneven feed, main motor bearing damage or poor lubrication, no heating. Faulty heater or incorrect phase, incorrect screw adjusting pad, component interference. Treatment method: Troubleshooting, check the feeder, replace the bearing if necessary. Repair the main motor and replace the heater if necessary. Check whether each heater is working properly, pull out the screws to check the interference of the screws, and check the adjustment pad. 2.

1. Multi-band automatic temperature control, high temperature alarm, humidification, moisture drainage, punctual switching machine, suitable for wood secondary drying, balance wood moisture content.2. Fast heating, uniform heating, less heat loss, can be combined disassembly, easy to move, suitable for leasing plant and wood processing enterprises.3. Diesel-electric dual use, concave value electricity at night, low cost; Burn wood by day, low price, kill two birds with one stone.

Industrial knife grinding machine can automatically adjust the grinding parameters according to the material and shape of different knives, and accurately complete the grinding, repair and maintenance of knives.Industrial knife grinding machine are suitable for grinding all kinds of knives, including but not limited to cutting knives, trimming knives, scrapers, milling cutters, turning tools, etc. Whether it is precision cutting, complex-shaped knives, or large-scale tool repairs, knife sharpeners can complete them accurately and quickly.