Wood Core Veneer Drying Line-manufacture,factory,supplier from China

The demand for wood veneer dryer is increasing year by year,and it has been recognized and purchased by consumers.Traditional natural air-dried wood is prone to problems such as deformation and cracking.The use of wood dryer equipment can effectively solve this problem.The cost of dryer equipment is high, so basic maintenance needs to be done in the later use process,such as the ground,ventilation system, gate,instrument,heating system and debugging system,etc.The specific operations are as follows:1.The floor of the wood dryer equipment should be kept clean and tidy,and the debris should be c

Recently, the veneer dryer provided by our company was successfully installed in Cambodia and has been put into use. Our engineers go to the customer's factory to guide the installation and will not return until the equipment is running normally and the workers are skilled in operation.The high reliability and low failure rate of veneer drying equipment greatly reduces equipment maintenance and downtime, and improves the overall operating efficiency of the production line.

Core veneer dryer principle is the core veneer in the upper and lower two pieces of coiler under the clamping preheating drying, coiler through the steam or heat conduction oil heating to transfer the temperature to the core veneer, high temperature coiler and wet core veneer direct contact, high thermal efficiency, heat loss is small, the core veneer is heated uniformly, the wood shrinkage of the benign physical process of evaporation, so the core veneer after drying the moisture content of the uniformity of the wood, the wood colour and lustre, inside and outside of the same, will not produc

Because the single board dryer is a long and large equipment, it is necessary to install the single board dryer in a correct sequence and method. The correct installation process is as follows:1. Draw the base line: make the cross line and elevation line correctly on the base plate.

Veneer dryers are mainly used in the veneer processing industry. Its purpose is to improve the stability and quality of veneers by removing moisture from the veneers, so that they are more suitable for subsequent processing and use. There are mainly the following common types of veneer dryers:Roller veneer dryersuitable for drying core boards. The veneers after drying have good flatness, uniform moisture content, and good surface bonding. Its working principle is to heat and dry the veneers with hot air. The hot air is generated by the combustion furnace and blown to the veneers by the fan.

Recently, our new customer successfully installed and put into use the 2 deck veneer dryer provided by our company. During normal operation, the veneer dryer has successfully completed the efficient drying of rubber wood veneers. Normal drying of rubber wood veneers can be dried to zero water, and the drying effect is satisfactory. It not only greatly improves the production efficiency of veneer processing, but also shows great advantages in environmental protection and energy saving.

Vietnamese customer's 40-meter single-layer veneer drying equipment is being installed. Due to the impact of the epidemic, the engineer cannot go to the site to install it. We will guide the customer to complete the installation smoothly through the video.

Introduction of technological veneerTechnological veneer is scientifically known as reconstructed decorative veneer, which is a kind of artificial wood veneer used for imitation of natural wood grain. Technological veneer is a wood surface material processed by modern scientific and technological means. It retains the texture and feel of natural wood through advanced production technology, while enhancing the physical properties of wood, such as wear resistance and corrosion resistance.

The wood veneer dryer needs to pay attention to some problems when drying wood. Before use, it should start the heating fan and start the speed regulating motor when reaching the drying temperature. The veneer should be entered longitudinally from the feed port, the feed should be straightened, the veneer and the drive roller into a 90 degree feed connection, before drying the veneer should be cut neatly. Drying should master the moisture content, according to the moisture content of the board, adjust the speed of the motor.Precautions for operation of wood veneer dryer1.

With the continuous demand of the wood industry for high efficiency and processing technology, veneer dryers, as key equipment for wood processing, have also made significant progress in technological innovation in recent years. The continuous advancement of technological innovation has also brought new opportunities to the market. Many companies have begun to pay attention to digital and automated drying technology to cope with market competition by improving production efficiency and reducing energy consumption.